Home

Awesome

Wellen

wellen is a framework for exploring and teaching generative music making and algorithmic compositions. it facilitates simple ways of playing musical notes, facilitates easy access to low-level digital signal processing (DSP) and supplies rhythm and timing as well as some standard muscial mechanics. the library acts as an adapter to various sound in- + outputs like MIDI, OSC, or digital/analog audio. the library is hosted on github wellen.

Installation

the library can be installed as a Processing library via the libray manager ( Sketch > Import Library… > Add Library… ) or by unpacking the wellen.zip archive into the Processing library folder. a step-by-step introduction to the library as well as extended applications can be found under examples.

Dependencies

wellen makes use of the oscP5 library to communicate over network with OSC ( see e.g ExampleExternal04OSCToneEngine ). the library can be installed via the processing library installer.

Concepts

in the screencast series Wellen some of the examples are explained in more detail. the text below explains the core concepts of the wellen library:

Tone

muscial notes can be played with a single call to Tone.note_on(int, int) and ended with Tone.note_off(int) ( see ExampleBasics01Notes ). each node is characterized by two parameters pitch and velocity. the value range conforms to MIDI standards.

by default a simple software-based synthesizer is used as a tone engine to produce the sound. however, there are quite a lot of options ( i.e an oscillator with different waveshapes, a low-pass filter (LPF), an attack-decay-sustain-release envelope (ADSR), and two low-frequency oscillators (LFOs) one for frequency and one for amplitude modulation ) to change the sound characteristics ( see ExampleBasics05Instruments + ExampleInstruments01ADSR ff. ).

the default tone engine is monophonic i.e a single instrument can play only one note at a time. however, there are 16 instruments available which can be combined into a polyphonic setup with 16 voices. instruments are handled in a state machine i.e that an instrument selected with Tone.instrument(int) will remain selected until another instrument is selected. it is common to select an instrument right before turning a note on or off e.g Tone.instrument(0); Tone.note_on(48, 85);. note that other tone engines might be polyphonic e.g in some MIDI applications.

although Tone is designed to play musical notes ( arranged in half-tone steps ) triggered by the note_on + note_off paradigm, it can also be used to controll the frequency and amplitude of the generated sounds directly ( see ExampleInstruments03FrequencyAndAmplitude ).

this schematic summarizes the relation of the different components that comprise an instrument in wellen. all components can be dis- + enabled ( see ExampleInstruments04LFOs + ExampleInstruments05LPF ) and overridden to implement custom behaviors ( see ExampleInstruments09CustomDSPInstrument ).

wellen comes with mechanisms to send messages to other applications or machines via MIDI ( see ExampleBasics06MIDI ) or OSC ( see ExampleExternal04OSCToneEngine ) or can even use multiple tone engines at the same time ( see ExampleExternal01MIDIToneEngineWithInternalToneEngine ). likewise wellen can also receive events from other applications or machines with EventReceiverMIDI via MIDI and EventReceiverOSC via OSC ( see ExampleExternal05ReceiveMIDIandOSC ).

DSP

wellen facilitates a mechanism for digital ( audio ) signal processing (DSP).

in the simplest setup the method DSP.start(Object) starts the signal processing pipeline which then continuously calls the method audioblock(float[]). the float[] array must be filled with samples that are then played back by the underlying audio infrastructure.

see ExampleBasics04DSP for a simple implementation of a sine wave oscillator as well as ExampleDSP03Echo for an implementations of slightly more advanced concept in DSP.

additionally DSP can also be started with different parameter sets to either run with stereo output ( see ExampleDSP01StereoOutput ), mono in- + output ( see ExampleDSP02PassThrough ) or stereo in- + output. additionally variations of the DSP.start(...) method allow to select other in- + output devices ( + sampling rate, audio block size, and number of in- + output channels ).

the default tone engine is designed to be optionally interfaced with DSP. this mechanism can e.g be used to apply an effect to played notes ( see ExampleDSP09ToneEngineInternalWithDSP ).

wellen comes with a series of handy classes to facilitate some fundamental DSP techniques. Sampler can be used to play back chunks of ( recorded ) memory at varying speed and direction ( see ExampleDSP07Sampler + ExampleDSP10SampleRecorder ). Wavetable is similar but designed to facilitate the emulation of oscillators with different wave shapes ( see ExampleDSP05Wavetable + ExampleDSP06LFO ). ADSR supplies an envelope to controll the amplitude of a signal over time. LowPassFilter allows the filtering of a signal with a resonance filter ( see ExampleDSP04LPF ). Trigger observes a continous signal and fires events whenever a rising or falling edge is detected; in conjunction with an oscillator it can be used to generate reoccuring events ( see ExampleDSP08Trigger ).

Beat

wellen has a mechanism to trigger a continous beat. the method Beat.start(Object, int) starts a beat at a specified beats per minute (BPM) ( see ExampleBasics03Beat ).

a beat can also be triggered by an external MIDI clock ( see ExampleExternal02MIDIClock ) to synchronize with other applications.

to synchronize a beat to DSP it can also be triggered by audio system requests ( see ExampleDSP11BeatDSP ).

Other Muscial Techniques

with Scale values can be transformed into intervals based on musical scales ( see ExampleBasics02Scales ).

the Sequencer supplies a simple structure to facilitate the recording and recalling of note sequences ( see ExampleTechnique01Sequencer ).

Arpeggiator works in a similar way but schedules a series of notes based on a predefined pattern and a base note.

Reference

generated reference of the library

Setup Internal MIDI Communication

macOS

macOS provides a mechanism to send virtual MIDI messages internally. the technique is called Inter-Application Communication (IAC). IAC can be used to send and receive MIDI messages ( e.g Note On/Off, Control Changes + MIDI Clock ). to configure IAC follow the steps below:

now the configured ports are avialable as virtual MIDI ports in macOS.

Wellen can list available MIDI ports with Wellen.dumpMidiInputDevices() + Wellen.dumpMidiOutputDevices(). the following examples demonstrate how to connect to MIDI devices, send and receive MIDI messages:

<!-- @todo(windows+linux) -->