Home

Awesome

TKey Programmer 1

The TKey Programmer 1 (TP1) board is a tool used to program the FPGA on a TKey. It consists of a RPI Pico and a jig where the TKey can be placed.

General usage

The board is interfaced using USB, and it will display itself as ID 1209:8886 Generic TP-1. The TKey is supposed to be placed in the jig and one closes the lid carefully by pressing in the middle of the jig (by the hole). To open the lid of the jig, it is easiest to simply lift up on the lever.

The TP1 board supports two host computer tools to accommodate programming of the TKey, either iceprog or pynvcm. See the chapter in the TKey Developer Handbook for a more elaborate description on how to use it.

Linux device permissions

To allow sudo-less programming, you need to be able to access the TKey Programmer USB device. This is a raw USB device that is probably not taken care of by your distribution.

You can install an udev rule that will assign the TP1 to the dialout group. You will also need to add your user to the dialout group.

Create the following udev rule at /etc/udev/rules.d:

# TP-1 programmer
SUBSYSTEM=="usb", ENV{DEVTYPE}=="usb_device", ATTR{idVendor}=="1209", ATTR{idProduct}=="8886", MODE="0666", GROUP="dialout"

To reload the rules run:

sudo udevadm control --reload-rules
sudo usermod -aG dialout ${USER}

To apply the new group, log out and then log back in, or run the command newgrp dialout in the terminal that you are working in.

You can check the device permissions to determine if the group was successfully applied. First, use lsusb to find the location of the programmer:

lsusb -d 1209:8886
Bus 001 Device 023: ID 1209:8886 Generic TP-1

Then, you can check the permissions by using the bus and device numbers reported above like this:

ls -l /dev/bus/usb/001/023
crw-rw---- 1 root dialout 189, 22 Feb 16 14:58 /dev/bus/usb/001/023

Note that this pair of numbers is ephemeral and may change after every device insertion.

Firmware

The TP1 board runs a custom firmware developed by Blinkinlabs for Tillitis. There is also a pre-built firmware binary at fw/bin/main.uf2.

To update the firmware, either build the file main.uf2 (more instructions below) or get the pre-built file to your host computer. Then do the following:

  1. Disconnect the programming board from the host computer
  2. Press and hold the "BOOTSEL" button on the RPi2040 sub-board on the programming board
  3. Reconnect the programming board to the host computer
  4. Release the "BOOTSEL" button after connecting the programming board to the host. The board should now appear to the host as a USB connected storage device
  5. Open the storage device and drop the firmware file main.uf2 into the storage device

The programmer will update its firmware with the file and restart itself. After rebooting, the storage device will automatically be disconnected.

Building the firmware

The firmware requires the Raspberry Pi Pico SDK, the build script assumes this is located either in your home home directory, or in /usr/local. To clone to the home directory use

cd ~
git clone --branch 1.5.1 https://github.com/raspberrypi/pico-sdk.git
cd pico-sdk
git submodule update --init

then run the build script in the fw folder

./build.sh

Note that our container image (tkey-builder) places the pico-sdk directory in /usr/local. For normal development, it is usually left in the user's home directory.

See fw/README.md for further instructions.

KiCad

The PCB is built using KiCad version 7. Production files are built in CI using KiBot, see the Makefile for exact version.

License

Hardware

Unless otherwise noted, this project is licensed under CERN Open Hardware License Version 2 - Strongly Reciprocal, see full license under LICENSE.txt.

Copyright Tillitis AB 2022-2024.

This source describes Open Hardware and is licensed under the CERN-OHL-S v2.

You may redistribute and modify this source and make products using it under
the terms of the CERN-OHL-S v2 (https://ohwr.org/cern_ohl_s_v2.txt).

This source is distributed WITHOUT ANY EXPRESS OR IMPLIED WARRANTY,
INCLUDING OF MERCHANTABILITY, SATISFACTORY QUALITY AND FITNESS FOR A
PARTICULAR PURPOSE. Please see the CERN-OHL-S v2 for applicable conditions.

Source location: https://github.com/tillitis/tp1

As per CERN-OHL-S v2 section 4, should You produce hardware based on this
source, You must where practicable maintain the Source Location visible
on the external case of the product or its packaging, and in its
documentation, even after modification.

The CERN-OHL-S user guide is included to make it easier to follow the license, both as a Licensor or a Licensee.

Firmware

The firmware running on the TP1 is licensed under MIT License, see the full license fw/LICENSE.

Copyright (c) 2023 Tillitis AB.

Raspberry Pi Pico

TKey Programmer board uses the Raspberry Pi Pico hardware, which are provided by Raspberry Pi Ltd. For more details, visit the official Raspberry Pi Pico documentation at https://www.raspberrypi.com/licensing/

Prototypes

Under prototypes/, an earlier version of the TP1 can be found, such as the mta1-usb-v1-programmer.

History

This repo was created by filtering out relevant commits and files from the tillitis/tillits-key1 repo.

The filtering removed all files and commits that weren't related to the tp1 hardware. This was done using git-filter-repo.

To replicate the results up until commit f1158b1 in this repo, checkout commit 354aecb in tillitis/tillitis-key1 and run git-filter-repo --path hw/boards/tp1 --path hw/boards/mta1-usb-v1-programmer --path hw/boards/KiCad-RP Pico

All filtered commits have intact date, author, and code. Some unrelated files are removed from some commits, but the commit messages are left unchanged. Commit sha, tags and signatures are new. For complete history, please see tillitis/tillitis-key1 from commit 354aecb and earlier.