Awesome

Turbo Resin: open-source firmware for resin printers

Turbo Resin is an open-source firmware for SLA resin printers.

This is the implementation of a firmware based on the Reverse engineering of the Anycubic Photon Mono 4K

Roadmap

Drivers:

• Read the touch screen
• Display on the touch screen
• Use the LVGL UI library
• Control the stepper motor
• Read/write to external Flash
• Read/write to external EEPROM
• Drive the LCD panel
• Read from USB flash drive
• Control the UV light
• Z=0 detection
• Being able to flash firmware via USB

Printing features:

• Better Z-Axis motion control for faster prints with fast deceleration
• Z=0 calibration
• Read .pwma files from USB flash drive
• Support multiple exposure (like RERF but configurable)
• Print algorithm
• Support more file formats to support various slicers
• Add support for other printers
• Build-plate force feedback for speed optimization. Following the work of Jan Mrázek
• Over-expose structural region of the print to add strength while letting edges be normally exposed

Support for other printers

The first set of printers we'd like to support are the AnyCubic, Phrozen, Elegoo, and Creality printers.

Sponsors

• Elliot from Tiny Labs
• @gnivler
• Madeleine

Thank you!

Flashing the firmware

As of now, there's no official distribution to flash the firmware via a USB stick. You'll need:

• A probe like JLink or ST-Link V2 ($11)
• A 3mm hex screwdriver

Compiling the firmware

Prerequisites

Install the Rust toolchain. Following instructions of the installation section of the Rust Embedded Book, run the following:

curl --proto '=https' --tlsv1.2 -sSf https://sh.rustup.rs | sh
source $HOME/.cargo/env
rustup component add llvm-tools-preview
cargo install cargo-binutils
# Ubuntu/Debian
sudo apt install -y gcc-arm-none-eabi gdb-multiarch libclang-dev openocd
# macOS
brew install armmbed/formulae/arm-none-eabi-gcc openocd

You are ready for building and flashing the firmware.

Configure the build

If you are using vscode, replace saturn with the printer of your choice in ./.vscode/settings.json

Configure the PRINTER, PROBE, and FLASH_WITH variables in the Makefile.

• PRINTER can be mono4k or saturn.
• PROBE can be jlink or stlink.
• FLASH_WITH can be jlink+gdb, or openocd+gdb, or probe-run. Pick the one that works for you.

Connect to the printer

Connect your JLink or ST-Link V2 probe to the SWD header on the printer board. Pinout is shown in Reverse engineering the Anycubic Photon Mono 4K Part1 You can also come and ask for guidance on our Discord channel.

make targets

• make start_probe: Starts the JLink or OpenOCD gdb server. You must run this in a separate terminal when using FLASH_WITH=jlink+gdb or FLASH_WITH=openocd+gdb prior to other commands.
• make start_probe_rtt: Show the logging statement emitted from the board.
• make run: Compile the code and flash the board
• make check: Check that the code is valid. (runs cargo check under the cover).
• make build: Builds the firmware to be flashed
• make flash: Flashes the compiled code to the board
• make attach: Provides a GDB console to the running code on board. Execute c and ctrl+c to break into a running target.
• make attach_bare: Provides a GDB console to the running code on board, but doesn't assume that the code running on the board is the one that was just compiled
• make restore_rom: Flashes back the original firmware. But you must dump the original firmware first. The instructions are shown when running this command.

License

Turbo Resin is licensed under the GPLv3, except for the USB Host stack, which is license under Apache 2.0 or MIT at your choice.