Awesome
MQTT-SN Tools
Command line tools written in C for the MQTT-SN (MQTT for Sensor Networks) protocol.
Supported Features
- QoS 0, 1 and -1
- Keep alive pings
- Publishing retained messages
- Publishing empty messages
- Subscribing to named topic
- Clean / unclean sessions
- Manual and automatic client ID generation
- Displaying topic name with wildcard subscriptions
- Pre-defined topic IDs and short topic names
- Forwarder encapsulation according to MQTT-SN Protocol Specification v1.2.
Limitations
- Packets must be 255 or less bytes long
- No Last Will and Testament
- No QoS 2
- No automatic re-sending of lost packets
- No Automatic gateway discovery
Building
Just run 'make' on a POSIX system.
Publishing
Usage: mqtt-sn-pub [opts] -t <topic> -m <message>
-d Increase debug level by one. -d can occur multiple times.
-f <file> A file to send as the message payload.
-h <host> MQTT-SN host to connect to. Defaults to '127.0.0.1'.
-i <clientid> ID to use for this client. Defaults to 'mqtt-sn-tools-' with process id.
-k <keepalive> keep alive in seconds for this client. Defaults to 10.
-e <sleep> sleep duration in seconds when disconnecting. Defaults to 0.
-m <message> Message payload to send.
-l Read from STDIN, one message per line.
-n Send a null (zero length) message.
-p <port> Network port to connect to. Defaults to 1883.
-q <qos> Quality of Service value (0, 1 or -1). Defaults to 0.
-r Message should be retained.
-s Read one whole message from STDIN.
-t <topic> MQTT-SN topic name to publish to.
-T <topicid> Pre-defined MQTT-SN topic ID to publish to.
--fe Enables Forwarder Encapsulation. Mqtt-sn packets are encapsulated according to MQTT-SN Protocol Specification v1.2, chapter 5.5 Forwarder Encapsulation.
--wlnid If Forwarder Encapsulation is enabled, wireless node ID for this client. Defaults to process id.
--cport <port> Source port for outgoing packets. Uses port in ephemeral range if not specified or set to 0.
Subscribing
Usage: mqtt-sn-sub [opts] -t <topic>
-1 exit after receiving a single message.
-c disable 'clean session' (store subscription and pending messages when client disconnects).
-d Increase debug level by one. -d can occur multiple times.
-h <host> MQTT-SN host to connect to. Defaults to '127.0.0.1'.
-i <clientid> ID to use for this client. Defaults to 'mqtt-sn-tools-' with process id.
-k <keepalive> keep alive in seconds for this client. Defaults to 10.
-e <sleep> sleep duration in seconds when disconnecting. Defaults to 0.
-p <port> Network port to connect to. Defaults to 1883.
-q <qos> QoS level to subscribe with (0 or 1). Defaults to 0.
-t <topic> MQTT-SN topic name to subscribe to. It may repeat multiple times.
-T <topicid> Pre-defined MQTT-SN topic ID to subscribe to. It may repeat multiple times.
--fe Enables Forwarder Encapsulation. Mqtt-sn packets are encapsulated according to MQTT-SN Protocol Specification v1.2, chapter 5.5 Forwarder Encapsulation.
--wlnid If Forwarder Encapsulation is enabled, wireless node ID for this client. Defaults to process id.
-v Print messages verbosely, showing the topic name.
-V Print messages verbosely, showing current time and the topic name.
--cport <port> Source port for outgoing packets. Uses port in ephemeral range if not specified or set to 0.
Dumping
Displays MQTT-SN packets sent to specified port. Most useful for listening out for QoS -1 messages being published by a client.
Usage: mqtt-sn-dump [opts] -p <port>
-a Dump all packet types.
-d Increase debug level by one. -d can occur multiple times.
-p <port> Network port to listen on. Defaults to 1883.
-v Print messages verbosely, showing the topic name.
Serial Port Bridge
The Serial Port bridge can be used to relay packets from a remote device on the end of a serial port and convert them into UDP packets, which are sent and received from a broker or MQTT-SN gateway.
Usage: mqtt-sn-serial-bridge [opts] <device>
-b <baud> Set the baud rate. Defaults to 9600.
-d Increase debug level by one. -d can occur multiple times.
-dd Enable extended debugging - display packets in hex.
-h <host> MQTT-SN host to connect to. Defaults to '127.0.0.1'.
-p <port> Network port to connect to. Defaults to 1883.
--fe Enables Forwarder Encapsulation. Mqtt-sn packets are encapsulated according to MQTT-SN Protocol Specification v1.2, chapter 5.5 Forwarder Encapsulation.
--cport <port> Source port for outgoing packets. Uses port in ephemeral range if not specified or set to 0.
License
MQTT-SN Tools is licensed under the MIT License.