Home

Awesome

pi-blaster

This project enables PWM on the GPIO pins you request of a Raspberry Pi. The technique used is extremely efficient: does not use the CPU and gives very stable pulses.

This project is based on the excellent work of Tomas Sarlandie pi-blaster: https://github.com/sarfata/pi-blaster and the modifications/updates made by Michael Vitousek: https://github.com/mvitousek/pi-blaster

Pi-blaster project is based on the excellent work of Richard Hirst for ServoBlaster: https://github.com/richardghirst/PiBits

How to build and install

This project is only distributed as source files. The build environment is based on Autotools to allow for compilation on the Raspberry Pi, or cross-compilation.

You may need to install 'autoconf' to build. On Raspbian and other Debian based systems this can be achieved with:

sudo apt-get install autoconf

Building is extremely simple:

./autogen.sh
./configure
make

To start pi-blaster and have it relaunched automatically on every reboot:

sudo make install

How to start manually

To start pi-blaster manually run:

sudo ./pi-blaster

How to uninstall

Simply run:

sudo make uninstall

This will stop pi-blaster and prevent it from starting automatically on the next reboot.

How to use

pi-blaster creates a special file (FIFO) in /dev/pi-blaster. Any application on your Raspberry Pi can write to it (this means that only pi-blaster needs to be root, your application can run as a normal user).

Important: when using pi-blaster, the GPIO pins you send to it are configured as output.

To set the value of a PIN, you write a command to /dev/pi-blaster in the form <GPIOPinName>=<value> where <value> must be a number between 0 and 1 (included).

  GPIO number   Pin in P1 header
      4              P1-7
      17             P1-11
      18             P1-12
      21             P1-13
      22             P1-15
      23             P1-16
      24             P1-18
      25             P1-22

Examples: Turning PWM pins ON

Examples: Turning PWM pins OFF (releasing a pin so it can be used as digital GPIO)

NodeJS Library

NodeJS users can use pi-blaster.js.

C#

A C# example was contributed by Vili Volcini. It is available on this stackoverflow thread.

How to adjust the frequency and the resolution of the PWM

On startup, pi-blaster gives you the frequency of the PWM, the number of steps that you can control, the maximum and the minimum period of a pulse.

sudo ./pi-blaster
Using hardware:                   PWM
Number of channels:                 8
PWM frequency:                 100 Hz
PWM steps:                       1000
Maximum period (100  %):      10000us
Minimum period (0.100%):         10us

You can adjust those by changing a few defines at the top of the source code:

If you do not neet a resolution of 1000 steps (approximately equivalent to a 10 bit DAC), then you can reduce the number of samples or increase the duration of the steps.

Richard Hirst who wrote the original code recommended not going below 2us for SAMPLE_US.

Options

To use the BCM2835's PCM peripheral instead of its PWM peripheral to time the DMA transfers, pass the option:

--pcm

This is useful if you are already using the chip's PWM peripheral, for example for audio output.

To invert the pulse (off = pin HIGH, pulse = pin LOW), use:

--invert

This can be useful for common anode LEDs or other devices that expect an active-low signal.

To view help or version information, use:

--help

--version

Warnings and other caveats

Pins being used by pi-blaster will be configured as outputs. Do not plug something on an input or you might destroy it!

This daemon uses the hardware PWM generator of the raspberry pi to get precise timings. This might interfere with your sound card output. There is experimental support for a PCM time-source. If you are interested, I suggest you look at Richard Hirst original project (ServoBlaster) and try the --pcm option.

A practical example: high-power RGB lighting

This library was developed for TBideas high power LED driver. You can read more about this project on our blog.

Contributors

Pete Nelson (https://github.com/petiepooo) Edgar Siva (https://github.com/edgarsilva) Alex Lennon (https://github.com/ajlennon) Lara Maia (https://github.com/LaraCraft304)

Want to support this project?

The best way to contribute is to write code for the features you would like to see and to make a pull-requests.

Another way is to send DogeCoin donations to D7pQ9CoUepazpGbwxgiaGPCMBk8i66u4yE. Donations will be used to help promote hardware hacking. For example by giving away servos and led strips during hackathons.

License

Released under The MIT License.

Note: This project was initially released by Richard Hist under the GPL v3 License. Richard gave me explicit permission to distribute this derivative work under the MIT License.

Copyright (c) 2013 Thomas Sarlandie - Richard Hirst

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.