Awesome

Cryologger - Iceberg Tracking Beacon (ITB)

Note: This project is under active development.

1.0 Introduction

Icebergs and ice islands represent significant hazards to marine navigation and offshore infrastructure at a time when demand for access to Canada’s Arctic waters is increasing. There is a growing demand for in situ iceberg tracking data to monitor their drift trajectory and improve predictions of ice hazard occurrence and behaviour, yet the high cost of commercial tracking devices often prevents monitoring at optimal spatial and temporal resolutions.

The Cryologger Ice Tracking Beacon (ITB), built using inexpensive, open-source hardware and software, provides a reliable and cost-effective platform for monitoring the drift of icebergs and ice islands in the Canadian Arctic.

2.0 Methods

2.1 Design

The Cryologger ITB is based on the open-source Arduino platform (www.arduino.cc) and built using low-cost, do-it-yourself electronics that can be easily modified to meet the needs of the end-user. Code was written using the Arduino Integrated Development Environment (IDE) and benefits from the availability of community-generated libraries.

Planned for extended deployments in harsh Arctic conditions, the Cryologger ITB provides long-term measurements of GNSS position, temperature, pressure, pitch, roll, tilt-compensated heading and battery voltage. Data are transmitted over the Iridium satellite network at specified intervals and can be remotely updated based on the desired sampling frequency. Collected data are made available in near-real time at https://cryologger.org.

2.1.1 Design Iterations

More information about the design of versions 1.0 and 2.0 of the Cryologger ITB can be found in the following publication:

Garbo, A., & Mueller, D. (2024). Cryologger Ice Tracking Beacon: A Low-Cost, Open-Source Platform for Tracking Icebergs and Ice Islands. Sensors, 24(4), Article 4. https://doi.org/10.3390/s24041044

Version 3.0 of the Cryologger ITB builds on the successes of previous versions and features a number of improvements to the design, including:

• 3.3 V power is now provided directly from a Pololu 3.3 V step-down voltage regulator, bypassing the Feather M0's onboard AP2112 LDO regulator (-55 μA).
• A dedicated 5 V step-down voltage regulator was added to power the RockBLOCK Iridium transceiver.
• The DS3231 real-time clock (RTC) was removed in favour of the SAMD21's internal RTC for all timekeeping and alarm functionality with periodic time synchronizations with the GPS.
• The LSM303 accelerometer/magnetometer was replaced with the LSM6DS33 + LIS3MDL IMU due to the sensor reaching its end-of-life (EOL).
• The temperature/pressure and IMU sensors are now powered directly through SAMD21 GPIO pins, allowing for power to be completely removed during sleep.
• A 10MΩ + 1 MΩ resistor divider is now used to measure the battery voltage (+2.4 μA).

A major change in v3.0 is a custom carrier board PCB that is designed to greatly simplify the assembly process. The PCB was designed in KiCad and fabricated by JLCPCB.

2.1.2 Bill of Materials (BOM)

Table 1. Bill of materials and associated costs for components used in the Cryologger ITB v3.1. Prices are listed in USD and are current as of December 2023. Taxes and shipping not included. ¹Denotes optional component. Please note BOM is a work in progress.

2.2 Operation

The programming logic of the Cryologger ITB optimizes sleep and wake cycles to minimize overall power consumption. When initially powered on, the system attempts to acquire a signal from the GNSS receiver and synchronizes the RTC with the current date and time. It then sets an alarm for the initial sampling interval and enters a low-power, deep-sleep mode. When the alarm triggers, the system wakes, records the time, and acquires a GNSS position. Next, measurements of all onboard sensors are collected (Table 2). These data are stored into memory and when the software determines the appropriate transmission interval has been met, it attempts to transmit the data using the RockBLOCK satellite transceiver. The software then disables power to all components, sets the next alarm, and returns to sleep.

2.2.1 Measurements

Table 2. Measurements recorded and transmitted by the Cryologger ITB v3.0, including variable sizes.

2.2.2 Data Transmission and Processing

The Cryologger ITB records its position and sensor measurements nominally on an hourly basis and transmits at an interval of 3 hours. Data are transmitted via the Iridium satellite network as a Short Burst Data (SBD) message. The ITB attempts to transmit each message for up to 180 seconds, and if unsuccessful, the message is stored in a temporary buffer and reattempted at the next transmission interval. Both the sampling and transmission frequency of individual Cryologgers can be remotely modified by the end-user. Successfully transmitted SBD messages are received by an Iridium ground station and sent to Ground Control's server. These data are then forwarded to Amazon Web Services (AWS), where they are decoded using a Python script, stored in a database, and visualized on the Cryologger website: https://cryologger.org.

3.0 Deployments

A total of 37 Cryologger ITBs have been deployed between 2018 and 2023 (Figure 3), primarily during the annual Amundsen Expedition. Deployments are performed by helicopter from the CCGS Amundsen on icebergs and ice islands along the coasts of Ellesmere Island, Baffin Island and Greenland (Figure 3). At the time of deployment, a compass heading of the tracking beacon was recorded. Where possible, a 360° aerial photo survey of the iceberg was performed for use with Structure-from-Motion photogrammetry to create 3D models of the iceberg.

The overall suitability of potential targets was determined by assessing the iceberg’s size, shape, and location. Where possible, icebergs selected to be instrumented with a tracking beacon were large enough to survive drifting south to the Grand Banks of Newfoundland and far enough away from the coast to increase the chances of being carried southward by the currents and avoid becoming grounded in shallow coastal areas.

4.0 Results

The operation of the Cryologger ITBs greatly exceeded expectations, with the operational lifespans of deployments made in 2018 ranging from 310 to 1530 days, and those in 2019 ranging from 333 to 615 days. The most frequent causes of loss of communication with the ITBs was due to the eventual deterioration (calving or rolling) or catastrophic break-up of the iceberg and subsequent destruction of the beacon. In many cases, it was possible to use remote sensing imagery to observe major break-up events of icebergs that immediately resulted in transmissions from the beacon ceasing.

4.1 Iceberg Drift

A snapshot of iceberg drift tracks recorded from all Cryologger ITB deployments as of December 2023 is shown in Figure 4. This data can also be viewed in real-time at: https://cryologger.org/tracking

5.0 Conclusion

The overall success of the Cryologger ITB has demonstrated that it can provide a robust platform for the collection of in-situ iceberg tracking data. With a total cost of approximately $700 USD in materials each, this represents a cost-effective alternative to existing proprietary commercial systems.

The development and deployment of these novel iceberg tracking beacons were intended to enhance and supplement existing iceberg observation networks within the Canadian Arctic and data collected from the Cryologgers has already contributed to a database of iceberg tracking beacon tracks compiled by the Canadian Ice Service (CIS). Most importantly, this research demonstrates to the scientific community that inexpensive, open-source hardware and software can provide a viable solution for the monitoring of icebergs and ice island drift patterns within the Canadian Arctic and beyond!

Development of the next iteration of the Cryologger ITB is currently underway, which is focused on improving overall reliability, exploring the use of environmentally friendly materials, and improvements that will allow it to transform into an ocean drifter buoy once the breakup of the icebergs occurs.

Repository Contents

• /Documentation - Assembly, deployment and troubleshooting guides, as well as information on components used and associated costs.

• /Hardware - KiCad PCB schematic and design files.

• /Software - Arduino code and Python data analysis scripts.

License Information

Cryologger code, firmware, and software is licensed under the GNU General Public License v3.0 (https://www.gnu.org/licenses/gpl-3.0.en.html).

Cheers,

Adam Garbo