Awesome
Gigabyte-Z590i-Vision-D-11900k
Within this repository I share my Hackintosh EFI for my newest build based on Intels Rocketlake 11th Gen CPU.
<p align="center"> <img src="Docs/Screenshot 2022-08-02 at 15.59.27.png" width="100%" align=center alt="Z590i and 11900k running macOS Ventura"> </p>Hardware used in this build:
- CPU: Intel i9-11900k
- Board: Gigabyte Z590i Vision D:
- Audio: Realtek ALC4080
- 1x 2.5GBase-T (Intel I225-V)
- 1x USB-C
- 2x Thunderbolt 4 ports (Intel JHL8540 Maple Ridge)
- 2x m.2 Slots
- RAM: 32GB G.Skill Trident Z 3600Mhz CL18
- AMD 6900XTXH (MSI Radeon RX 6900 XT Gaming Z)
- Wifi/BT: Intel AX201, replaced by a Broadcom BCM94360NG for macOS Compatibilty. Works out of the box. The BCM94360NG fits into the original WiFi-card housing and sits under the IO-shield. Original antennas fit.
- SSDs: 1x 2TB Samsung 980 Pro OEM (PM9A1) for Windows 10 (sits in the m.2 below the CPU) 1x 1TB Samsung 960 EVO for macOS (sits on the back of the board)
- Case: NCASE M1 v6.1
What is working:
- SMBIOS MacPro7,1 with full h264/h265 hardware encoding
- Audio: working out of the box as it is connected like a USB-Audio interface. But keep in mind it only shows up, when you plugin something (e.g. headphones).
- Thunderbolt 4 (incl. Hotplug, tested with Monterey 12.5 and Ventura Beta 5)
- Replacing the internal m.2 Intel Wifi with a BCM94360NG to have macOS native Wifi/BT Support
- USB-ports. Have created my custom USB port mapping with USBMap.command
What is not working:
- iGPU, the 11th Gen iGPU is not supported by macOS
Wifi in macOS Sonoma
With macOS Sonoma, the Broadcom based Wifi cards don't work plug and play anymore. It is a very annoying process now, that you have to repeat after every macOS Update!
General Requirements for Broadcom Wifi in Sonoma:
- Additional Kexts:
IO80211FamilyLegacy.kext
,IOSkywalkFamily.kext
,AMFIPass.kext
. Also these Kexts in a very high priority after Lilu and VirtualSMC. - Blocking Kexts:
com.apple.iokit.IOSkywalkFamily
- Bootarg:
-amfipassbeta
- NVRAM:
csr-active-config=<03080000>
To be repeated for every macOS Update:
- Disable SecureBoot via config.plist:
SecureBootModel = Disabled
andDmgLoading = Any
Disable SecureBoot
in BIOS- Install the macOS Update
- Run the OCLP Patcher and start the "Post-install Root Patch".
- Enable SecureBoot via config.plist:
SecureBootModel =
(your SecureBootModel according to here: https://dortania.github.io/OpenCore-Post-Install/universal/security/applesecureboot.html#securebootmodel) andDmgLoading = Any
- Enable SecureBoot in BIOS again
Getting the OpenCore Legacy Patcher
Install the newest release from here: https://github.com/dortania/OpenCore-Legacy-Patcher/releases
USB Port Mapping
Update (05.01.23): Z590 Vision D Users I have added a USB port configuration for the ATX version Z590 Vision D as well. You just have to disable SSDT-USB-Ports-Z590i-VisionD.aml and enable SSDT-USB-Ports-Z590-VisionD.aml.
<p align="center"> <img src="Docs/USB-port-configuration-Z590i-VisionD%232.png" width="100%" align=center alt="USB Port Mapping Z590i Vision D"> </p>BIOS-settings:
- Current BIOS version: F8b
- Load optimized defaults
- Set Above 4G Decoding to Enabled
- Set Legacy USB Support to Disabled
- Set Intel VT-D to Enabled (DisableIOMapper is disabled, AppleVTD should be working)
- Set Internal Graphics to Disabled (or Auto if you want to use it in Windows)
- Thunderbolt:
-
Discrete Thunderbolt Support: Enabled
-
Wake From Thunderbolt Devices: Disabled
-
Native OS security for TBT: Disabled
-
Discrete Thunderbolt Configuration:
-
Thunderbolt USB Support: Disabled
-
Thunderbolt Boot Support: Disabled
-
Titan Ridge Workaround for OSUP: Disabled
-
Tbt Dynamic AC/DC L1: Disabled
-
GPIO3 Force Pwr: Enabled
-
Wait time in ms after applying Force Pwr: 200
-
GPIO filter: Enabled
-
DTBT Controller 0 Configuration: all Settings in this Submenu BIOS-Default
-
- For Secure Boot:
- Set Secure Boot to Enabled
- Set Secure Boot Mode to Custom
- Go to Key Management and then Enroll EFI.
- Add all *.efi Files in your EFI Folder: BOOTX64.efi, all drivers(OpenRunTime.efi, OpenHFSPlus.efi, OpenCanopy.efi), OpenCore.EFI
FYI: I have XMP Profile disabled because I noticed stability issues in macOS. I am using the RAM with 2133Mhz now.
<p align="center"> <img src="BIOS_Settings/IMG_4756.jpg" width="100%" align=center alt="BIOS settings #1"> <img src="BIOS_Settings/IMG_4757.jpg" width="100%" align=center alt="BIOS settings #2"> <img src="BIOS_Settings/IMG_4758.jpg" width="100%" align=center alt="BIOS settings #3"> <img src="BIOS_Settings/IMG_4759.jpg" width="100%" align=center alt="BIOS settings #4"> <img src="BIOS_Settings/IMG_4760.jpg" width="100%" align=center alt="BIOS settings #5"> <img src="BIOS_Settings/IMG_4763.jpg" width="100%" align=center alt="BIOS settings #6"> <img src="BIOS_Settings/IMG_4761.jpg" width="100%" align=center alt="BIOS settings #7"> <img src="BIOS_Settings/IMG_4762.jpg" width="100%" align=center alt="BIOS settings #8"> </p>Credits:
- ohchang Your Z590 Vision G config was very helpful!
- CaseySJ, Ori69 and vipermachine For the Thunderbolt 4 support!
- Dortania for this great OpenCore Desktop Guide
- headkaze for Hackintool and our productive conversations :)
- Acidanthera for too many things to mention each
- RehabMan for too many things to mention each
- OpenCore project for this great bootloader