Awesome
Habitat LoRa Gateway
Part of the LoRa Balloon Tracking System. Receives balloon telemetry and uploads to Sondehub and/or MQTT.
<u>ALL HABHUB SUPPORT HAS BEEN REMOVED since that server has been decommissioned</u>
<u>If you are updating from an old version, please see the MQTT section below to install a library that you will need to build the latest version.</u>
Runs on a Raspberry Pi with 1 or 2 RFM98HW modules attached to the SPI port. Also works with other compatible HopeRF and Semtec LoRa devices.
Connections
If you're making your own board for the Pi, connect the LoRa module(s) like so:
LORA PI
---- --
3.3V 3.3V Power
GND Ground
MOSI MOSI (pin 19)
MISO MISO (pin 21)
NSS CE0 (pin 24) (CE1 (pin 26) for 2nd module)
SCK SLCK
DIO0 Wiring Pi 31 (Pin 28) (Wiring Pi 6 (pin 22) for 2nd module)
DIO5 Wiring Pi 26 (Pin 32) (Wiring Pi 5 (pin 18) for 2nd module). Set to -1 if not connected.
SPI
Enable SPI in raspi-config
Dependencies
sudo apt-get install git libcurl4-openssl-dev libncurses5-dev libssl-dev
SSDV
Raspberry Pi OS no longer includes SSDV, so you must install SSDV from source as follows:
cd ~
git clone https://github.com/fsphil/ssdv.git
cd ssdv
make
sudo make install
WiringPi
Raspberry Pi OS no longer includes WiringPi, so you must install Wiring Pi from source as follows:
cd ~
git clone https://github.com/WiringPi/WiringPi.git
cd WiringPi
./build
MQTT
MQTT support was added recently, and needs the following library installed::
cd ~
mkdir MQTTClients
cd MQTTClients
git clone https://github.com/janderholm/paho.mqtt.c.git
cd paho.mqtt.c
make
sudo make install
Gateway
cd ~
git clone https://github.com/PiInTheSky/lora-gateway.git
cd lora-gateway
make
cp gateway-sample.txt gateway.txt
Configuration
The configuration is in the file gateway.txt. Example:
tracker=M0RPI
EnableSondehub=Y
EnableSSDV=Y
LogTelemetry=Y
LogPackets=Y
CallingTimeout=60
JPGFolder=ssdv
CallingTimeout=60
ServerPort=6004
Latitude=51.95023
Longitude=-2.5445
Radio=LoRa RFM98W
Antenna=868MHz Yagi
frequency_0=434.347
mode_0=1
DIO0_0=31
DIO5_0=26
AFC_0=N
frequency_1=434.475
mode_1=5
DIO0_1=6
DIO5_1=5
AFC_1=Y
The global options are:
tracker=<callsign>. This is whatever callsign you want to appear as on the tracking map and/or SSDV page.
EnableHabitat=<Y/N>. Enables uploading of telemetry packets to Habitat.
EnableSondehub=<Y/N>. Enables uploading of telemetry packets to the amateur Sondehub system.
EnableSSDV=<Y/N>. Enables uploading of SSDV image packets to the SSDV server.
EnableHABLink=<Y/N>. Enables uploading of telemetry packets to the hab.link server.
JPGFolder=<folder>. Tells the gateway where to save local JPEG files built from incoming SSDV packets.
LogTelemetry=<Y/N>. Enables logging of telemetry packets (ASCII only at present) to telemetry.txt.
LogPackets=<Y/N>. Enables logging of packet information (SNR, RSSI, length, type) to packets.txt.
SMSFolder=<folder>. Tells the gateway to check for incoming SMS messages or tweets that should be sent to the tracker via the uplink.
CallingTimeout=<seconds>. Sets a timeout for returning to calling mode after a period with no received packets.
ServerPort=<port>. Opens a server socket which can have 1 client connected. Sends JSON telemetry and status information to that client.
HABPort=<port>. Opens a server socket which can have 1 client connected. Port is a raw data stream between gateway and HAB (e.g. for Telnet-like communications). Note: The corresponding functionality at the tracker end has not been published.
DataPort=<port>. Opens a server socket which can have 1 client connected. Sends raw telemetry (i.e. $$payload,....) to that client.
HABTimeout=<ms>. Timeout in case of no response from HAB to raw data uplink.
HABChannel=<channel>. Specifies LoRa channel (0 or 1) used for telnet-style communications.
Latitude=<decimal position>
Longitude=<decimal position>. These let you tell the gateway your position, for uploading to habitat, so your listener icon appears on the map in the correct position.
Radio=<radio make/model>. Lets you specify your radio/board make/model or type. This appears on the map if your listener icon is clicked on.
Antenna=<antenna make/model>. Lets you specify your antenna make/model or type. This appears on the map if your listener icon is clicked on.
NetworkLED=<wiring pi pin>
InternetLED=<wiring pi pin>
ActivityLED_0=<wiring pi pin>
ActivityLED_1=<wiring pi pin>. These are used for LED status indicators. Useful for packaged gateways that don't have a monitor attached.
and the channel-specific options are:
frequency_<n>=<freq in MHz>. This sets the frequency for LoRa module <n> (0 for first, 1 for second). e.g. frequency_0=434.450
PPM_<n>=<Parts per million offset of LoRa module.
AFC_<n>=<Y/N>. Enables or disables automatic frequency control (retunes by the frequency error of last received packet).
mode_<n>=<mode>. Sets the "mode" for the selected LoRa module. This offers a simple way of setting the various
LoRa parameters (SF etc.) in one go. The modes are:
0 = (normal for telemetry) Explicit mode, Error coding 4:8, Bandwidth 20.8kHz, SF 11, Low data rate optimize on
1 = (normal for SSDV) Implicit mode, Error coding 4:5, Bandwidth 20.8kHz, SF 6, Low data rate optimize off
2 = (normal for repeater) Explicit mode, Error coding 4:8, Bandwidth 62.5kHz, SF 8, Low data rate optimize off
3 = (normal for fast SSDV) Explicit mode, Error coding 4:6, Bandwidth 250kHz, SF 7, Low data rate optimize off
4 = Test mode not for normal use.
5 = (normal for calling mode) Explicit mode, Error coding 4:8, Bandwidth 41.7kHz, SF 11, Low data rate optimize off
SF_<n>=<Spreading Factor> e.g. SF_0=7
Bandwidth_<n>=<Bandwidth>. e.g. Bandwidth_0=41K7. Options are 7K8, 10K4, 15K6, 20K8, 31K25, 41K7, 62K5, 125K, 250K, 500K
Implicit_<n>=<Y/N>. e.g. Implicit_0=Y
Coding_<n>=<error_coding>. e.g. Coding_0=5 (4:5)
lowopt_<n>=<Y/N>. Enables or disables low data rate optimization.
power_<n>=<power>. This is the power setting used for uplinks. Refer to the LoRa manual for details on setting this. ** Only set values that are legal in your location (for EU see IR2030) **
UplinkTime_0=<seconds>. When to send any uplink messages, measured as seconds into each cycle.
UplinkCycle_0=<seconds>. Cycle time for uplinks. First cycle starts at 00:00:00. So for uplink time=2 and cycle=30, any transmissions will start at 2 and 32 seconds after each minute.
Lines are commented out with "#" at the start.
If the frequency_n line is commented out, then that channel is disabled.
The program now performs some checks to determine if each selected LoRa module is present or not. If you see a message "RFM not found on Channel" then check the SPI settings/wiring for that channel. If you see "DIO5 pin is misconfigured on Channel" then check the DIO5 setting/wiring. There is no current check for DIO0; any problems with that pin will result in packets not being received.
Uplinks
The gateway can uplink messages to the tracker. Currently this is restricted to time-based uplink slots using "UplinkTime" and "UplinkCycle".
The code uses Linux system time, so the gateway should ideally be using a GPS receiver the GPSD daemon. NTP may prove sufficient however.
For uplinks to work, both UplinkTime and UplinkCycle have to be set for the appropriate channel.
There are currently two types of uplink supported:
- Uplink of messages from the "SMSFolder" folder. For this to work, "SMSFolder" has to be defined and present. The gateway will then check for "*.sms" files in that folder.
- Uplink of SSD packet re-send requests. The gateway looks for an "uplink.txt" file in the gateway folder. The file is created by an external Python script (supplied) which interrogates the SSDV server.
Calling Mode
It is possible for trackers to send out messages on a special "calling channel" as well as telemetry on their main frequency. The calling channel messages state the main frequency and LoRa modes.
This allows for gateways tp be normally left on the calling channel, so they then switch to each tracker as it comes within range.
There's nothing special about "calling mode" except that after a period (CallingTimeout seconds) of time without packets, the gateway returns to its default settings.
To enable calling mode, set the LoRa mode to 5, and the frequency to 433.650MHz.
MQTT
To send telemetry to an MQTT broker, edit the MQTT settings in gateway.txt
e.g.:
# MQTT Config
EnableMQTT=Y
MQTTHost=mqtt_host
MQTTPort=1883
MQTTUser=mqtt_user
MQTTPass=mqtt_password
MQTTClient=mqtt_client_name
MQTTTopic=topic_name
Display
The display has a title bar at the top, scrolling log at the bottom, and 2 channel panels in the middle. Each panel shows something like:
Channel 0 869.8500MHz
Explicit, 250k, SF7, EC4:6
Telemetry 74 bytes
51.95028, -2.54443, 00138
Habitat SSDV 0000
0s since last packet
Telem Packets = 37
Image Packets = 0
Bad CRC = 0 Bad Type = 0
Packet SNR = 10, RSSI = -67
Freq. Error = 1.0kHz
Current RSSI = -64
The "Habitat" text appears during uploads to habitat. Normally it will flash up then disappear quickly; if it stays on (not flickering) then the upload is slow.
The "SSDV 0000" text shows the current state of the SSDV upload buffers. There are 4 upload threads and each can handle up to 16 (0-9-A-F) packets in its queue. Normally, even with fast SSDV, uplinks should happen quickly enough for there to be no more than 1 or 2 active threads each with 1 packet being uploaded.
Interactive Features
The following key presses are available. Where appropriate unshifted keys affect Channel 0 and shifted keys affect Channel 1. Many thanks to David Brooke for coding this feature and the AFC.
q quit
a increase frequency by 100kHz
z decrease frequency by 100kHz
s increase frequency by 10kHz
x decrease frequency by 10kHz
d increase frequency by 1kHz
c decrease frequency by 1kHz
f toggle AFC
Change History
08/10/2023 - V1.10.6
Use callsign for MQTT client ID
08/10/2023 - V1.10.5
Fully handle all documented Sondehub responses - see https://github.com/projecthorus/sondehub-infra/wiki/API-(Beta)#notes-on-api-response-codes
14/9/2023 - V1.10.4
Clear InUse flag in SH upload so new telemetry is only uploaded once
2/9/2023 - V1.10.3
Limit to 5 retries on SH upload
24/8/2023 - V1.10.2
UKHAS Telemetry is CRC16 checked before being used/uploaded, in addition to the existing LoRa CRC check
Separation of new incoming telemetry and that already being uploaded to Sondehub
Added parsing check on UKHAS telemetry before uploading to Sondehub
13/8/2023 - V1.10.1
Sondehub upload: For errors, log return code, return text and uploaded JSON to errors.txt
1/2023 - V1.10.0
Removed all HABHUB Support
13/10/2022 - V1.9.6
Sondehub upload: Interpret battery voltage as V/mV automatiically
Sondehub upload: Send battery voltage in V
24/09/2022 - V1.9.5
Sondehub datetime field now contains payload timestamp plus current UTC date, corrected if necessary for UTC being the day after the telemetry was created (i.e. telemetry just before midnight UTC received just after midnight)
24/09/2222 - V1.9.4
Include UKHAS sentence as "raw" value sent to sondehub/amateur
Remove any "/" character from listener callsign sent to sondehub/amateur
21/09/2022 - V1.9.3
Scans telemetry for a fieldlist field. This is metadata defining the sequence of fields in the telemetry string
If found, then this field is used to extract fields such as sats, pred_lat etc., and send them to Sondehub/amateur
10/09/2022 - V1.9.2
Fixed code that uploads to Sondehub so that a zero altitude doesn't result in a 400 response from the server
Any 400 responses are now logged to errors.txt along with the JSON that triggered them
A 400 response is no longer retried
05/09/2022 - V1.9.1
Only upload to Sondehub if telemetry has non-zero latitude or longitude
04/09/2022 - V1.9.0
Added support for uploading telemetry and listener details to the amateur Sondehub system.
16/02/2022 - V1.8.46
Added flexible MQTT topic - $GATEWAY$ gets replaced by gateway callsign; $PAYLOAD$ gets replaced by payload callsign
14/02/2022 - V1.8.45
Added MQTT support (coded by David Johnson G4DPZ)
02/02/2022 - V1.8.44
Fix to uplink of encrypted commands.
19/03/2021 - V1.8.43mbb
Added radio setting to gateway.txt
07/03/2021 - V1.8.43
Fixed erors in setting implicit/explicit bit on config register when sent from JSON client. Thanks to Alan Hall for spotting this one.
23/02/2021 - V1.8.42
Can now disable use of DIO5 by setting DIO5_0=-1 or DIO5_1=-1
20/02/2021 - V1.8.41
telemetry.txt file includes LoRa channel 0 or 1
08/02/2021 - V1.8.40
Fixed bug where JSON server stopped when asked to set parameters for missing LoRa Module
If you are using the gateway with HAB Base or PADD and just 1 LoRa module you *need* this update.
25/11/2020 - V1.8.39
Send callsign, listener type (LoRa Gateway) and version to hab.link server
Don't include callsign with telemetry messages to hab.link server
06/05/2020 - V1.8.38
Send current frequency to client app, with current RSSI
06/05/2020 - V1.8.37
Reset AFC offset to zero after setting frequency from client app
10/02/2020 - V1.8.35
Fix to RSSI calculation when SNR < 0 (thanks to Alan Hall)
03/02/2020 - V1.8.34
Maximum payload ID (callsign) length in telemetry or calling mode is now 31 (was 15).
03/02/2020 - V1.8.33
Set length of received buffer with strlen() instead of using rx byte count, to avoid sending dross to clients (by Steve Randall)
19/01/2020 - V1.8.32
By proboscide99:
Parameters received in a calling mode packet are saved. If the channel is also used for UpLink, saved
parameters will be restored after transmission. This allows immediate reception with correct parameters
without having to wait for a new calling mode packet.
Fixed bug that forced 255 bytes in missing SSDV packet request (UpLink mode) even with 'explicit headers'
When 'implicit headers' are used for UpLink mode, buffer is NULL terminated to prevent the tracker
from processing garbage (danger)
Both channels may be used for UpLink mode using different timing in the uplink slot (leave 1-2 secs gap)
Timeout for seeking for missing SSDV file 'uplink.txt' reduced from 2sec to 300ms to allow small gap
between channels (see above)
Fixed bug measured frequency offset was retained when AFC timeout occurs (affects value set by keys)
Fixed bug that prevented listener from being uploaded to map (longitude comparison)
Channel number display added to many messages on log console
08/01/2020 - V1.8.31
Fixed bug measured frequency offset was retained when returning to calling mode
Fixed bug where uplink messages were not set to 255 bytes in implicit mode
Fixed bug where listeners with longitude between -180 and -90 were not uploaded to map
13/06/2019 - V1.8.30
Added ability to connect to hab.link server for responsive web dashboards.
13/06/2019 - V1.8.29
Fixed bug where only the first sentence in a multi-sentence packet was uploaded to Habitat
Fixed bug where the message uplink sent 255 bytes even if message was shorter
Fixed bug where after leaving help screen screen shows original frequency not AFC'd frequency
Fixed bug where AFC correction was lost after uplink
AFC correction is now upplied to uplink
09/05/2019 - V1.8.28
Store all payloads from combined packet for JSON transmission to client.
09/05/2019 - V1.8.27
Reduced RSSI server port output frequency from 10Hz to 1Hz
13/04/2019 - V1.8.26
Extended UDP status output with basic channel settings
11/03/2019 - V1.8.25
UDP broadcast output of gateway hostname, IP address and version number.
27/02/2019 - V1.8.24
Better colours
autostart.pdf added to show how to autostart the software and use screen to easily attach to it.
Thanks to Steve Hyde for these.
27/02/2019 - V1.8.23
Chat mode settings
12/09/2018 - V1.8.22
Added PPM setting and correction
09/05/2018 - V1.8.21
Remove superfluous trailing zeroes from the ASCII telemetry produced from HABPack
04/05/2018 - V1.8.20
Included HABPack decoding by Phil Crump M0DNY
16/04/2018 - V1.8.19
Disabled DIO5 check for now as it sometimes disabled use of a working device.
11/04/2018 - V1.8.18
JSON port now sends packet SNR, RSSI and frequency error
Implemented callbacks for when settings are changed
Reprogram LoRa module when frequency, bandwidth etc are changed via JSON port
Update display when frequency, bandwidth, AFC etc are changed via JSON port
10/04/2018 - V1.8.17
JSON port only sends telemetry as it is received, instead of repeatedly
JSON port now sends current RSSI
Append \r\n to sentences sent to data port
JSON port now accepts commands split over multiple packets (e.g. typed commands)
When saving to gateway.txt, permissions are set to RW/RW/RW, and owner/group are maintained
Added Sockets.md to document the available sockets.
06/04/2018 - V1.8.16
Added raw output of $$... sentences to specified port (UDPPort=xx in gateway.txt)
Added OziMux format output (TELEMETRY,time,lat,lon,alt) to specified port (OziPort=xx)
26/03/2018 - V1.18.15
By Phil Crump:
Detect if DIO5 isn't correctly mapped (default level != high), warn and disables the channel.
Detect if the RFM isn't responding (reg 0x42 == 0x00), warn and disables the channel.
Warn if both receivers are disabled or unconfigured.
Removed message queue test code - functionality was behind that of the main code path, and would have required updating for the other changes in this set.
Added storage of at-time-of-receive-configuration in rx_metadata_t struct. This is copied into the queued telemetry_t structure when a Telemetry Packet is processed.
Added upload of receiver frequency (with detected offset) to Habitat with payload telemetry ( Issue #15 ). Mostly ported from Pull Req #28 which has been tested by @dbrooke .
Added logging of additional metadata parameters in packet.log (Issue #5 )
Removed duplicate 'LogTelemetryPacket()' call in habitat thread. (Already called in ProcessTelemetryMessage)
By me:
Added "Dataport" server socket for raw data (like port 7322 in dl-fldigi)
Added "<" sentence type, for telemetry that is not to be uploaded to Habitat.
12/02/2018 - V1.8.14
By Phil Crump:
Added separate thread for listener telemetry/information upload (Listener telemetry is uploaded every 30 minutes to maintain map marker)
Corrected incremental tuning units 'MHz' -> 'kHz', and added lowercase letters in tuning lookup table
By me:
Added config description to this file for telnet-like HAB communications link
01/10/2017 - V1.8.12
Added null uplink option
Test for incoming null uplink message
21/09/2017 - V1.8.11
Added mode 8 (fastest settings for 62k 10% section of IR2030), for SSDV repeater network
11/09/2017 - V1.8.10
Fixed issue introduced in V1.8.8 which broke processing of repeated telemetry packets (those beginning with a "%" to show repeated)
01/09/2017 - V1.8.9
Added mode 7 for Telnet uplink
Incorporated changes to support Telnet-style terminal to HAB
28/08/2017 - V1.8.8
Do not assume telemetry sentence has a LF at the end
Do not assume telemetry has 2 $ signs at beginning
18/04/2017 - V1.8.7
New help screen added to show the available commands.
Press H to access this feature
Fixed a padding bug on telemetry line !
??/??/2017 - V1.8.6
27/09/2016 - V1.8.5
New config setting - AFCMaxStep - limits AFC delta to this amount in kHz for each new packet
New config setting - AFCTimeout - Resets AFC changes if no packets received in this period (in seconds)
If gateway.txt missing, and gateway-sample.txt present, rename latter as former
Fixed SSDV upload status marker
Fix to frequency format when retuning after calling mode
Some log display messages now only appear if the feature they describe is in use
15/09/2016 - V1.8.4
Fix to handle disabled channel
14/09/2016 - V1.8.3
Save boolean settings sent by client
Use of atexit() so ncurses is always closed properly on exit
Added an exit-with-message function
Fixed errors where threads were closed on exit even if they hadn't been created (i.e. their functions disabled in the config)
Consistent RSSI calculations that take HF/LF port into account
14/09/2016 - V1.8.2
Configuration all in a generic array
Generic code to read/write config array/file
Send configuration values to JSON client
Accept commands and new config settings from client
Fixed SMS folder error
Fixed LDRO setting
03/09/2016 - V1.8
Add configuration of uplink frequency, mode and power
LoRa modes now in array so easier to add new ones
Added LoRa mode for uplink
Re-instated logging to telemetry.txt
Fixed pipe errors which happened if packets arrived during program exit
Merged in changes to JSON format
Sends data both LoRa channels in JSON
Config disables CE0 by default (most cards have CE1 only)
Fixed typos in gateway-sample.txt
Accept new SSDV types
25/08/2016 - V1.7
Robert Harrison (RJH) has made numerous changes.
Highlights include :-
Changed makefile to include -Wall and fixed all warnings generated
Added pipes for Inter-Process Communication
Moved none thread safe curl funtions from threads and into main()
Added reporting of curl errors to habitat and ssdv threads
Changed color to green but requires 256 color support in your terminal
For putty users please set your terminal as shown
when you are connected to your pi
# echo $TERM # should show something with 256 in
or
# tpu colors # Should show 256
27/06/2016 - V1.6
Single SSDV upload thread using new API to upload multiple packets at once
Fixed 100% CPU (SSDV thread not sleeping)
23/05/2016 - V1.5
Better status screen
13/05/2016
Bug fux to local conversion of large SSDV images
Added packet logging
04/04/2016
SSDV 8 buffers
JSON feed instead of old "transition" method
19/02/2016
Fixed listener_information JSON
Added antenna setting to gateway.txt
16/02/2016
JSON telemetry feed via a server port
JPEGFolder setting
Uplink of text messages to tracker (e.g. accepted from Twitter by an external script)
Uplink of SSDV re-send requests. These requests are built by an external Python script.
Separate thread for uploading latest telemetry to habitat
4 separate threads for uploading SSDV packets to the SSDV server
Slightly different display layout, with extra information
07/10/2015
fsphil: Tidied up compiler warnings, makefile, file permissions