Home

Awesome

Ergo42

The Answer to the Ultimate Question of Life, the Universe, and at least Keyboards.

7x4 ortho linear split keyboard.

Ergo42

Caution! Ergo42 after version 3.0.0 Towel is not compatible with both version 1 and 2 series design. If you build Ergo42 not version 3 Towel series, please refer to the 1.x or 2.x branch.

Parts

The screws may have a slight clearance issue with the keycaps. Use a screw with a lower profile head.

Mount the diodes

Place the PCB as TRRS jacks on the inside, closest to one another.

Which side you solder the diodes on depends on your switch plate's thickness and key switch type, which is Cherry MX compatible or Kailh low profile. Acrylic plate thickness < 3 mm with Cherry MX compatibles should have diodes on the same side as the key switches. Acrylic plate with Kailh low profile switches should have diodes on the opposite side of the key switches.

Double check your work. Black lines (THD) / White lines (SMD) should be facing the square pad.

diodes_01

[Optional] Mount the resistors and bridge jumper

If you want to use I2C, not UART, to comunicate with other side PCB, you should add 2.2 k ohm resistors on the left side PCB's R1 and R2 printed silk. Also bridge to short W1 pad by solder jumper on each side PCB. Usually you don't have to do this step.

Mount the TRRS Jack and tact switch

Mount the TRRS jack and tact switch on the same side as your switches. It should be on the upper face.

Mount the Pro Micro

Ergo42's PCB is symmetrical but Pro Micro mount is different between the left and right PCB. This spec is changed from version 2.

Pro Micro and pin header

Solder pin headers on the Pro Micro's component side. Both left side and right side one are same.

Soldered pin header

Through hole connector

If you use through hole connectors, you should solder that on the Pro Micro board, not on the PCB.

The through hole connector has sides and directions. There is recommended mount direction.

Through hole connector directions and sides

Please mount the through hole connector on the Pro Micro referencing the direction on the image above. Also be careful to mount the through hole connectors to face same side on same direction. You can see the holes on both through hole connectors simultaneously. Please check that the holes of the through hole connector is visible at the same time in the image below.

Soldered pin header

Solder (or set) the Pro Micro

Solder (or set when you use through hole connector) the Pro Micro on the PCB in the white line silk.

Soldered pin header

Soldered pin header

Be careful to refer the white line on the Pro Micro side (not soldering side).

Mount switches

Mount switches on the acrylic plate, set PCB to fit and solder switches.
When you use Cherry MX compatibles with Acrylic plate thickness < 3 mm and 5 mm height stand-offs, please cut off the tip of the electricity terminal of the switch. The electricity terminal of the switch interferences with bottom plate.

Assemble the case

Tighten the screws with standoffs. Some vinyl pads may help the keyboard's stability. Install your keycaps.

From version 3 Towel, there are some tent/tilt leg options. You can set the legs and put on some silicon tape for stability.

Flash QMK Firmware

To flash the pre-built firmware hosted by Remap

Now you can flash the pre-built firmware that supports VIA / Remap keymap edit in Remap.

https://remap-keys.app/catalog/unf8swoIgYlDVLGyN9H6

To build your own firmware

QMK firmware for Ergo42 is now available on QMK firmware. This document doesn't cover how to build QMK. Prease refer to QMK documents.

Connect the keyboard by USB cable to a PC and run

$ make ergo42:default:avrdude

on the left and right side keyboard individually.

It will build and try to flash your firmware. Follow the instructions that require to reset the Pro Micro.

This process may require privileges. If you have some Permission denied error, please try

$ sudo make ergo42/rev1:default:avrdude

All done!